服務熱線：4007-1100-10
Description:
Klübersynth UH1 6 oils are gear and
high-temperature oils on a polyglycol
basis.
They comply with the German law
governing foodstuffs and associated
ancillaries (LMBG, §5/1) and meet
the requirements set forth in the
Guidelines of Sec. 21 CFR
178.3570 of FDA regulations. These
oils comply with the USDA H1
requirements
Klübersynth UH1 6 oils meet the
CLP requirements; in the FZG Four
Square Gear Oil Tester acc. to DIN
51 354, pt. 2, A/8.3/90, these oils
achieve a scuffing load stage of
> 12 and a specific change in
weight < 0.2 mg/kWh. In the
enhanced FZG test A/16.6/90 the
Klübersynth UH1 6 oils with a
viscosity ISO VG 220 or higher had
a scuffing load stage of > 12.
Klübersynth UH1 6 oils offer
corrosion protection, ageing and
oxidation resistance, shear stability
as well as high-temperature
stability.
Application:
Klübersynth UH1 6 oils were
especially developed for the
lubrication of worm gears with
steel/bronze pairings. Due to the
special polyglycol base oils and
additives, these oils reduce friction
and wear considerably.
Klübersynth UH1 6 oils are also
suitable for the lubrication of bevel
and spur gears including machine
elements such as plain and rolling
bearings, especially when exposed
to high temperatures.
Furthermore, they can be used to
lubricate lifting, drive and transport
chains.
Application notes:
Klübersynth UH1 6 oils can be
applied by immersion, immersion
circulation and injection.
Klübersynth UH1 6 oils are not
miscible with mineral oils and
synthetic hydrocarbons. We
recommend cleaning the lubrication
points or rinsing gears or closed
systems with the Klübersynth
UH1 6 oil which will be used after
conversion.
Especially with a view to the H1
requirements in the food-processing
industry, any mixing of Klübersynth
UH1 6 oil with non-food-grade
lubricants should be avoided.
Klübersynth UH1 6 oils are neutral
towards ferrous metals and almost
all nonferrous metals. There may be
increased wear when the contact
surfaces of design elements made
of aluminium or aluminium alloys
are exposed to dynamic loads
(sliding speed and high loads).
If necessary, preliminary tests
should be carried out.
For permanent temperatures at the
seal edge up to 100 °C, NBR seals
(acrylonitrile-butadiene rubber) may
be used. For higher temperatures, it
is safer to use FKM seals
(fluorinated rubber) instead.
It should be noted that elastomers
from the one or several manufacturers
can behave differently.
Therefore, the data given in the
“compatibility with elastomers” table
should be used for reference
purposes only. A compatibility test
should always be carried out with
the elastomers which are actually
used.
We recommend using twocomponent
paints (reaction paints).
Oil gauge glasses should preferably
be made of natural glass or
polyamide materials.
The suitability of design materials
and paints in contact with
Klübersynth UH1 6 oils should be
tested, especially prior to series
application.
Viscosity selection for rolling
bearings:
To select the correct oil viscosity
observe the bearing manufacturer’s
instructions or refer to worksheet 3
from the Society of Tribology (GfT).
東莞市灝瑞潤滑油科技有限公司銷售克魯勃 1kg，針對克魯勃 1kg客戶提供相關咨詢服務，需要了解克魯勃 1kg型號尺寸、重量、價格、安裝、維護等資料請與我們聯系。
東莞市灝瑞潤滑油科技有限公司
經營模式：貿易型
所在地區：廣東 東莞
掃碼打電話